In terms of efficiency, the type linier not so good, because in the process of the output penyearah derived through the linear tegangannya (linear regulator), and the difference between the incoming voltage and the voltage generated in the form of discarded heat. Due to absorption of heat (energy disposal) are in the process of linear type so that even a small efficiency. While on the type of switching, the efficiency improvement is achieved with the magnetic fields due to the difference between the output voltage inputs. Setting is associated with the storage and disposal of energy magnet, which at the time of the energy storage component in the magnet until a certain point energy, the switch that is used to send power to the load is turned off (off state), and energy storage components and magnet before taking over task switch to send the stored power to the load. When the 'savings' energy magnets are running out earlier, the switch is turned on again (on state) to take back the task of sending power to the load and simultaneously began to restore energy magnets to repeat the same process. But in this paper, we only restrict the set of converter type DC to DC, if there is information on the similarity between the series of AC to DC converter with DC to DC then can be explained with a possible general description above.
As mentioned previously, that in this paper we will only describe the converter is a DC to DC diversiform created as a means of making a project that aims to produce a converter that has inputan 50-100 Volt DC output and is 12 behind volt.latar the making of this paper is requesting a tool that has a 12 Volt output to complete a specific tool that can not be fulfilled by the tool that has a voltage that has been there.
A. DC to DC CONVERTER
Converter is a tool that contains a series of high voltage modifier into low voltage or vice versa. Changes can occur in the voltage range of DC to Dc, AC to AC, AC to DC or AC to DC. the tool is not only seen in the way of the voltage but also on the flow of power or with a certain efficiency, depending on the use of components and system design.
Modifier power DC-DC (DC-DC Converter) of the type known as the DC Chopper used for the provision of DC voltage output that varies with demand besarannya depending on load. Power input from the DC-DC is derived from the DC power source that usually has a fixed input voltage. DC voltage is generated want can be achieved with a set length of time the connection between the inputs and outputs on the same series, In general there are two functions of the operation of the DC voltage rise Chopper where the output voltage generated from the higher voltage
inputs, and decrease the output voltage where the voltage is lower than the input voltage.
A good converter is the converter output has a fixed and stable. To produce the soft output and the absence of amplitude changes in the voltage converter is limited by 100 mVpp is controlled by the capacitor and also a limited 250 mVpp is controlled by induktor. besides, the converter must be properly protected by a series of protection to avoid the occurrence of konsleting. How it works is a series of protection that is the way of achievement of specified levels of cash through pensettingan, when the buck is off converer
As mentioned previously, that in this paper we will only describe the converter is a DC to DC diversiform created as a means of making a project that aims to produce a converter that has inputan 50-100 Volt DC output and is 12 behind volt.latar the making of this paper is requesting a tool that has a 12 Volt output to complete a specific tool that can not be fulfilled by the tool that has a voltage that has been there.
A. DC to DC CONVERTER
Converter is a tool that contains a series of high voltage modifier into low voltage or vice versa. Changes can occur in the voltage range of DC to Dc, AC to AC, AC to DC or AC to DC. the tool is not only seen in the way of the voltage but also on the flow of power or with a certain efficiency, depending on the use of components and system design.
Modifier power DC-DC (DC-DC Converter) of the type known as the DC Chopper used for the provision of DC voltage output that varies with demand besarannya depending on load. Power input from the DC-DC is derived from the DC power source that usually has a fixed input voltage. DC voltage is generated want can be achieved with a set length of time the connection between the inputs and outputs on the same series, In general there are two functions of the operation of the DC voltage rise Chopper where the output voltage generated from the higher voltage
inputs, and decrease the output voltage where the voltage is lower than the input voltage.
A good converter is the converter output has a fixed and stable. To produce the soft output and the absence of amplitude changes in the voltage converter is limited by 100 mVpp is controlled by the capacitor and also a limited 250 mVpp is controlled by induktor. besides, the converter must be properly protected by a series of protection to avoid the occurrence of konsleting. How it works is a series of protection that is the way of achievement of specified levels of cash through pensettingan, when the buck is off converer
0 comments: